Skip to content

Korean Risk Assessment in 5 Steps: 2026 Guide

Updated

Korean risk assessment runs in five stages, and its statutory duties on worker participation and sharing results became stronger on June 1, 2026. The stages are preparation, hazard identification, risk determination, control planning and implementation, and recording and communication. Records must show who took part, what was done, and how the results were shared. When an operator reports an unusual sound from rotating equipment, the team needs to check the work scope and current controls.

Current as of July 12, 2026.

Workers seen from behind holding a start-of-shift toolbox talk beside rotating equipment

Illustrative image

Korean risk assessment checks at each stage

Stage Key question Evidence to retain
1. Preparation Which process and task are in scope? Scope, owners, schedule, and criteria
2. Hazard identification Who could be harmed, and by what? Walkthroughs, worker input, accident and near-miss data
3. Risk determination Is the risk tolerable with current controls? Decision criteria and priorities
4. Control and implementation Were elimination, substitution, and engineering controls considered first? Owner, due date, and completion result
5. Record and communicate Is the action complete, and do workers know the residual risk? Verification, training, toolbox talks, postings, or electronic notice

Five-stage Korean risk assessment and monthly weekly daily continuous review cycle

Figure 1. Five risk assessment stages connected to monthly, weekly, and daily review. Source: Ministry of Employment and Labor risk assessment guide and official notice.

Assessment of a hypothetical unusual-sound report

A worker wearing ear defenders checking the bearing housing of a running pump by hand

Illustrative image

Define the task and inspection boundary first. The operator and maintenance worker then examine when the sound occurs, the condition of guards, access during operation, and potential entanglement or crushing hazards. Apply the workplace decision criteria, assign controls such as stopping and isolating the equipment, qualified inspection, or guarding, and set the restart conditions. Before work resumes, tell the crew what risk remains.

The signal is an input to hazard identification, not the assessment itself. Risk determination, control implementation, verification, and worker communication still have to follow.

Risk assessment flow from an unusual rotating-equipment sound report to restart

Figure 2. A worked flow from an unusual-sound report through scope confirmation, risk assessment, controls, and restart records.

Continuous review: month, week, day

Workplaces with frequently changing hazards can run a continuous assessment instead. Ministry guidance connects a monthly joint labor-management walkthrough, a weekly safety discussion, and a daily pre-work toolbox meeting.

  • Monthly: review the full workplace, new hazards, and incomplete controls.
  • Weekly: fold in process changes and planned work, then reset priorities.
  • Daily: communicate the hazards and controls for the work about to start.

This is not the same form produced every day. Monthly findings shape weekly coordination and daily work instructions, and field observations feed the next review.

Five failure points, five fixes

  1. A manager completes the assessment alone. Involve the workers who know the task in identifying hazards and reviewing controls.
  2. Hazards get listed and nothing else. Give every control an owner and a due date.
  3. Equipment or the process changes while the old assessment stays on file. Reassess whatever changed.
  4. Nobody verifies completion. Recheck residual risk after controls go in, and record the result.
  5. Results are recorded but not shared. Communicate the outcome and pre-work precautions to workers; participation and communication are part of the statutory duty now.

Include non-routine work such as maintenance, cleaning, and restart in the scope. Set the risk decision criteria before assessing, and consider elimination and substitution before personal protective equipment.

Start the next assessment with incomplete actions and newly identified hazards in the previous records. The accumulated records document each process's hazard history and the participation required by the June revision.

When the first clue is a sound

Acoustic and vibration data can support hazard identification alongside worker reports. Motor Sound Diagnostics analyzes condition signals from motors, reducers, and other rotating equipment and flags anomalies to help define inspection scope and targets. On-site teams remain responsible for risk determination, controls, and worker participation.

Official sources

Previous guide: 2026 Korean Workplace Safety Law Changes by Date

Next guide: Serious Accidents Punishment Act: Nine Duties

Author XylolabsPublished
Share

← Back to blog